Hover over each step to see a larger view
|
Exploded View |
|
|
Step Explanations: |
|
This diagram shows all the parts of the Orb and the corresponding number of each part.
To avoid any misunderstanding, please refer to these names and numbers when discussing
the Orb assembly with your consultant.
Orb Components
- Bottom Orb Shell (Base)
- Bottom Button (Bottom Ring Assembly)
- Positive Ring (Sharp Edge facing UP)
- Positive Track
- Centre Module (Copper & two Rings)
- Positive Ring (Sharp Edge facing DOWN)
- Top Button (Top Ring Assembly)
- Top Orb Shell
- Cable Connector (Mohawk)
- Locking clip
|
|
Step 1a. Begin with the Bottom Shell
(Orb Base) |
|
 |
Step Explanations: |
|
Begin the Assembly by taking the Bottom Orb
Shell (#1).
Take note of the brass post recess as shown
here. |
|
Step 1b. Insert the first Ring with
Brass Post. |
|
 |
Step Explanations: |
|
Press the Bottom
Button (#2) into the Bottom Orb Shell with
the Brass Post pointing down to fit into the
recess. |
|
Step 2. Inserting the 2nd Ring. |
|
 |
Step Explanations: |
Place one Positive
Ring (#3) into the Orb Shell.
For
optimal performance please ensure that the
less-rounded edge of the Positive Ring face
up. |
|
Step 3. Inserting the Positive Track. |
|
 |
Step Explanations: |
|
Place the Positive Track (#4) into the Orb
Shell, resting on (A) the Positive Ring and
(B) the indent on the Orb Shell. |
|
Step 4. Inserting the Centre Module. |
|
 |
Step Explanations: |
Fit the Centre Module (#5) into the Orb Shell
between the Positive Track arms as shown,
(B) ensuring that the Negative Track (A) is
directly opposite the Positive Track.
The Centre Module (#5) should rest on the
Bottom Button (#2) and be level within the
Orb Shell. |
|
Step 5. Inserting the 2nd Positive
Ring. |
|
 |
Step Explanations: |
Place the remaining Positive Ring (#6) into
the Orb resting on top of the Positive Track
(#4) as shown (A).
For optimal
performance please ensure that the
less-rounded edge of the Positive Ring faces
down.
|
|
Step 6a. |
|
 |
Step Explanations: |
|
Take the Top Orb Shell (#8) and locate the
hole in the top. |
|
Step 6b. Inserting the Top Button. |
|
 |
Step Explanations: |
|
Insert the Top Button (#7) into the Top Orb
Shell so that the Brass Post protrudes
through the hole. Gently rotate it so that
it goes in smoothly. It should hold in
firmly. |
|
Step 7a. Fitting the Top Orb Shell. |
|
 |
Step Explanations: |
|
Align the arrows (A) on the rear of the Orb
Shell. When placed correctly, the Tab on the
rear of the Bottom Orb Shell (B) will match
up with the Hole (B) on the rear of the Top
Orb Shell. |
|
Step 7b. Closing the Top Orb Shell. |
|
 |
Step Explanations: |
|
Close the Top and Bottom Orb shells as if
hinged at the back. The small indent in the
Top Shell (C) will align with the Positive
Track Eyelet (#4). |
|
Step 8a. Locate Guide Slots. |
|
 |
Step Explanations: |
|
Locate the Guide Slots and the Top Slot in the
Orb. |
|
Step 8b. Fitting the Cable Connector. |
|
 |
Step Explanations: |
|
Slide the tip of the Cable Connector (#9) into
the Top Slot of the Orb. Align the Guide
Pins with the Guide Slots in the Orb and
push the Cable Connector firmly against the
Orb. |
|
Step 9. Locking the Cable Connector in
place. |
|
 |
Step Explanations: |
|
Ensure that there is no gap between the Orb
and the Cable Connector. Whilst holding the
Cable Connector firmly against the Orb,
slide the Locking Clip (#10) upward
fastening the Cable Connector to the Orb. |
|
Step 10. Locking the Cable Connector in
place. |
|
 |
Step Explanations: |
|
Ensure the Locking Clip clicks over the top of
the Locking Pins on the Cable Connector. |
|
Your Orb
is now complete. |
|
 |
Step Explanations: |
|
Your Orb is now complete and ready to begin a
Q ENERGYspa session. |
|
Remember to never use force, and
if in doubt, please call your nearest support centre.
|
